Bonjour,
j’ai reçu pour Noël donc je suis un novice, un ender 3 pro avec la carte V4.2.2 avec Marlin ver 0.0.6 le 30 mai 2020.
Comme j’ai beaucoup de problèmes pour niveler le lit, j’ai acheté et reçu un BLtouch de Creality
Je veux savoir étape par étape comment installer ce BLtouch, comment et avec quel firmware je dois mettre à jour le firmware qui se trouve actuellement dans mon ender 3 pro et où le télécharger.
Vous trouverez des photos de mon Ender 3 pro actuel.
Merci d’avance pour vos réponses complètes
Cordialement
Ender 3 Pro
CR-6 SE
LD-002H + UW-01
up please
Ender 3 Pro
CR-6 SE
LD-002H + UW-01
@christ49fr Sorry for the late reply. Actually, installing the BL touch on the Ender3 pro with the V4.2.2 mainboard is very easy. May I ask if your BL touch wire is 5 pins port or 2+3 pins port?
https://www.youtube.com/watch?v=Xiy-oLLrB1k
You can refer to this video.
As for the firmware, you can download it here: Ender-3 Pro-4.2.2 Marlin2.0.1-BL-Touch-V1.1.2 (without adapter board)
https://forums.creality3dofficial.com/download/ender-series/ender-3-pro/
Bonjour Kevin, merci pour ta réponse J’avais peur de ne pas avoir de réponse.
Le câble de mon BL touch est à 3 broches mais les couleurs sont inversées (regardez ma photo) de plus je viens de regarder votre vidéo YT et je vois que dans cette vidéo la couleur des câbles est toujours différente de celle de mon câble
but my motherboard is 4.2.2
Ender 3 Pro
CR-6 SE
LD-002H + UW-01
@christ49fr The colour may be different if the bl touch made by a different supplier. If you have the user Manual, you should be able to find out which colour stands for what. Then there are some marks on the mainboard, just be careful with the sequence。
Yes, your board is 4.2.2, so you need to download the Ender-3 Pro-4.2.2 Marlin2.0.1-BL-Touch-V1.1.2 (without adapter card)”
The V1.1.2 is the version of BL touch, never mind it.
Ok thank you for your answer, I can not understand one thing however I have other questions.
1st: you have understood that I want to connect my Bl touch (your creality product) to the Bl touch port which is on my motherboard 4.2.2 and if I want to connect it thus I cannot because the GND cable (blue here) is in the middle when he must be on the Left!
2nd: If I read the manual included with the Bl touch again, I have to use Pinboard A
3rd: what are the differences if I connect my Bl touch to the Pinboard or to the Bl touch port on the motherboard
All this is not very comprehensive!
Ender 3 Pro
CR-6 SE
LD-002H + UW-01
up please
Ender 3 Pro
CR-6 SE
LD-002H + UW-01
@christ49fr Hi.. With sharp knife lift plastic lip you can change connector.
Manual is not updated with 4.2.2 board, only for old V2 , 32bit main board.
Don’t have to use adapter board, just plug in Bl touch port on the motherboard.
Use firmware version
Ender-3 Pro- 4.2.2
Marlin2.0.1 – BL-Touch-V1.1.2(without adapter board)
https://forums.creality3dofficial.com/download/ender-series/ender-3-pro/
