Forum


 

CR-10 Smart firmwar…
 
Notifications
Clear all

[Sticky] CR-10 Smart firmware source code

8 Posts
3 Users
4 Likes
1,185 Views
GregO1778
(@grego1778)
New Member
Joined: 7 months ago
Posts: 4
Topic starter  

Hello all,

I wanted to request the updated source code of the Marlin firmware for the CR-10 Smart.

Thank you.


   
ReplyQuote
TheMaskGuy
(@themaskguy)
New Member
Joined: 7 months ago
Posts: 3
 

@grego1778 Have you had issues with new update? 


   
ReplyQuote
GregO1778
(@grego1778)
New Member
Joined: 7 months ago
Posts: 4
Topic starter  

I have not had a specific issue however there a marlin supported features that are disabled by default that i would like to enable.

Also, being a software developer its important that licensing agreements are followed for else it hurts all of us developers in the long run and causes more and more software to become closed source. Currently the marlin licensing agreement is in violation until the creality firmware is made publicly available


   
mdburkey and ForestQC69 reacted
ReplyQuote
GregO1778
(@grego1778)
New Member
Joined: 7 months ago
Posts: 4
Topic starter  

I have not had a specific issue however there a marlin supported features that are disabled by default that i would like to enable.

Also, being a software developer its important that licensing agreements are followed for else it hurts all of us developers in the long run and causes more and more software to become closed source. Currently the marlin licensing agreement is in violation until the creality firmware is made publicly available


   
ForestQC69 reacted
ReplyQuote
ForestQC69
(@forestqc69)
New Member
Joined: 5 months ago
Posts: 3
 

I would also like to request the Firmware source code to be able to recompile it. I send an email 1 month ago and still didn’t receive any answer, not even an acknowledgement!

 

I changed my hotend and thermistor and I need to change the thermistor type in the configuration.h file and set the sensor to type 1 (#define TEMP_SENSOR_0 1)

 

I’d also like to see/know what is the thermistor type used currently for stock CR-10 Smart just for the sake of it..

 

I’d also like to note that Creality is violating the license of the Marlin code under the GPLv3, and that they NEED to make a copy available upon request. The Marlin crew has been publicly made aware of that at : https://twitter.com/ForestQC69/status/1517164149100396546


   
ReplyQuote
ForestQC69
(@forestqc69)
New Member
Joined: 5 months ago
Posts: 3
 

I would also like to request the Firmware source code to be able to recompile it. I send an email 1 month ago and still didn’t receive any answer, not even an acknowledgement!

 

I changed my hotend and thermistor and I need to change the thermistor type in the configuration.h file and set the sensor to type 1 (#define TEMP_SENSOR_0 1)

 

I’d also like to see/know what is the thermistor type used currently for stock CR-10 Smart just for the sake of it..

 

I’d also like to note that Creality is violating the license of the Marlin code under the GPLv3, and that they NEED to make a copy available upon request. The Marlin crew has been publicly made aware of that at : https://twitter.com/ForestQC69/status/1517164149100396546


   
ReplyQuote
ForestQC69
(@forestqc69)
New Member
Joined: 5 months ago
Posts: 3
 

@grego1778 did you get the source firmware?


   
ReplyQuote
GregO1778
(@grego1778)
New Member
Joined: 7 months ago
Posts: 4
Topic starter  

Hi ForestQC69;

Sorry I didn’t reply sooner, I gave up on the site once Creality refused to follow the terms of the license on Marlin.

Shirt answer is I still have not seen the source by I’m still looking and will probably jump to a custom firmware until Creality decides to release it.

Have you had any luck?


   
mdburkey reacted
ReplyQuote